- المجال: Oil & gas
- Number of terms: 8814
- Number of blossaries: 0
- Company Profile:
The sample obtained at the bottoms-up time or a volume of fluid to pump, as in "pump bottoms-up before drilling ahead. "
Industry:Oil & gas
The separation of phases of an emulsion with the lighter phase on top and denser phase on bottom. When oil muds are stagnant, the less dense oil phase rises and the denser aqueous phase settles. This behavior is not necessarily related to emulsion weakness, nor does it portend breaking, as does coalescence.
Industry:Oil & gas
The salt of aluminum hydroxide and stearic acid (saturated C-18 fatty acid) with the formula Al(O<sub>2</sub>C<sub>18</sub>H<sub>35</sub>)<sub>3</sub>. It is a grease-like solid. When mixed with oil (for example, diesel oil) and the mixture sprayed onto the surface of a foamy water mud, it helps the gas bubbles break out of the mud.
Industry:Oil & gas
The rubblized rock just below the tooth of a rock bit. Rock in the crushed zone fails due to the high compressive stress placed on it by the bit tooth (in the case of a roller-cone bit). The effective creation of and removal of crushed zone rock is important to the efficiency of the drill bit. If the rock is not broken and removed efficiently, the result is akin to effectively drilling the hole twice.
Industry:Oil & gas
The revolving or spinning section of the drillfloor that provides power to turn the drillstring in a clockwise direction (as viewed from above). The rotary motion and power are transmitted through the kelly bushing and the kelly to the drillstring. When the drillstring is rotating, the drilling crew commonly describes the operation as simply, "rotating to the right," "turning to the right," or, "rotating on bottom. " Almost all rigs today have a rotary table, either as primary or backup system for rotating the drillstring. Topdrive technology, which allows continuous rotation of the drillstring, has replaced the rotary table in certain operations. A few rigs are being built today with topdrive systems only, and lack the traditional kelly system.
Industry:Oil & gas
The residue deposited on a permeable medium when a slurry, such as a drilling fluid, is forced against the medium under a pressure. Filtrate is the liquid that passes through the medium, leaving the cake on the medium. Drilling muds are tested to determine filtration rate and filter-cake properties. Cake properties such as cake thickness, toughness, slickness and permeability are important because the cake that forms on permeable zones in the wellbore can cause stuck pipe and other drilling problems. Reduced oil and gas production can result from reservoir damage when a poor filter cake allows deep filtrate invasion. A certain degree of cake buildup is desirable to isolate formations from drilling fluids. In openhole completions in high-angle or horizontal holes, the formation of an external filter cake is preferable to a cake that forms partly inside the formation. The latter has a higher potential for formation damage.
Industry:Oil & gas
The representative of the oil company or operator on a drilling location. For land operations, the company man is responsible for operational issues on the location, including the safety and efficiency of the project. Even administrative managers are expected to respond to the direction of the company man when they are on the rigsite. Offshore, depending on the regulatory requirements, there may be an offshore installation manager, who supervises the company man on safety and vessel integrity issues, but not on operational issues.
Industry:Oil & gas
The report sheets filled out by the mud engineer at the wellsite on a daily basis. The mud report supplies results of tests performed several times per day as well as details about mud product usage, inventory, recommendations and other pertinent information. Multiple-copy forms in a format approved by the API, which are provided by the mud service company, are the traditional type of mud report. Today, mud reports are more likely to be computerized and transmitted electronically.
Industry:Oil & gas
The repair or stimulation of an existing production well for the purpose of restoring, prolonging or enhancing the production of hydrocarbons.
Industry:Oil & gas
The relatively small work area in which the rig crew conducts operations, usually adding or removing drillpipe to or from the drillstring. The rig floor is the most dangerous location on the rig because heavy iron is moved around there. Drillstring connections are made or broken on the drillfloor, and the driller's console for controlling the major components of the rig are located there. Attached to the rig floor is a small metal room, the doghouse, where the rig crew can meet, take breaks and take refuge from the elements during idle times.
Industry:Oil & gas
